NEWS

Great news
Click Online Message

TEL:0391-5299981

EMAIL:qyyangnan@vip.163.com

ADDRESS:South Section of Taihang Avenue, QinYang

Industry news
Great news
Home > Juli News > Industry news

Type bending machine

Release time:2012-09-26 09:29:33 Source of the article:qyjljc Number of clicks:1690

  Type bending machine

  The hydraulic bending machine processes the Q235 sheet for a brief introduction:

  First, turn on the power, turn on the key switch on the control panel, and then press the oil pump to start, so you will hear the sound of the oil pump. (The machine does not work at this time)

  Second, the stroke adjustment, the use of the bending machine must pay attention to adjust the stroke, must test the car before bending. A bending gap must be ensured when the upper die of the bending machine goes down to the bottom. Otherwise it will cause damage to the mold and machine. The adjustment of the stroke also has an electric quick adjustment and a manual stomach adjustment.

  Third, the choice of bending slot, generally choose the slot thickness of 8 times the thickness of the plate. For bending 4mm sheets, you need to choose a notch of about 32.

  Fourth, the rear material adjustment generally has electric quick adjustment and manual fine adjustment, the same method as the shearing machine.

  5. Press the foot switch to start bending. The bending machine is different from the shearing machine. You can release it at any time. When you release the foot bending machine, it will stop and continue to descend. Bending machine safety operation procedures Edit this paragraph 1. Strictly follow the safe operation rules of machine tools, wear protective equipment according to regulations.

  6. Before starting, carefully check whether the motor, switch, circuit and grounding are normal and firm. Check the operating parts of the equipment and the button is in the correct position.

  Check the overlap and firmness of the upper and lower molds; check that each positioning device meets the requirements for machining.

  7. When the upper slide plate and each positioning axis are not in the state of the origin, the homing program is run.

  8. After the equipment starts, it will run for 1-2 minutes, and the upper slide will move 2-3 times. If it is found that there is abnormal sound or there is a fault, it should stop immediately, and the fault will be eliminated.

  IX. The work should be unified by one person, so that the operator can closely cooperate with the feeding and suppressing personnel to ensure that the matching personnel can issue the bending signal in a safe position.

  10. When the sheet material is bent, it must be compacted to prevent the sheet from being warped and injured when bending.

  11. When the sheet material is pressed, the power must be cut off and stopped after the operation.

  12. When changing the opening of the variable lower mold, no material is allowed to come into contact with the lower mold.

  13. When the machine is working, the rear of the machine is not allowed to stand.

  14. It is strictly forbidden to press the sheet at one end separately.

  15. When the workpiece or mold is found to be incorrect during operation, it should be stopped for calibration. It is strictly forbidden to correct by hand during operation to prevent injury.

  16. It is forbidden to fold over-thick iron plates or quenched steel plates, alloy steels, square steels and sheets exceeding the performance of sheet bending machines to avoid damage to the machine.

  17. Check the overlap of the upper and lower molds frequently; whether the indication of the pressure gauge meets the requirements.

  18. Abnormal shutdown immediately, check the cause and eliminate it in time.

  19. Before shutting down, place wooden blocks on the lower mold below the cylinders on both sides to lower the upper slide to the wooden block.

  Twenty, first exit the control system program, then cut off the power.



  • PHONE
  • message
    MESSAGE
  • map
    MAP
  • ewm
    QR CODE
  • 国产r67194吃奶视频| 亚洲国产欧美在线人成精品一区二区 | 久久久www免费人成精品| 手机在线观看av片| 中文字幕精品在线观看| 性xxxxfreexxxxx国产| 丁香六月久久久| 夜夜躁日日躁狠狠久久av| a级黄色毛片免费播放视频| 国产色视频在线| 3d动漫wxxxx在线播放| 国产成人精品日本亚洲| 色噜噜狠狠一区二区三区| 国产一区二区免费在线| 皇后羞辱打开双腿调教h| 伊人久久中文字幕| 欧美成a人片在线观看久| 亚洲伊人色欲综合网| 日本猛妇色xxxxx在线| 久久久亚洲欧洲日产国码农村 | 成人欧美一区二区三区在线| 三级极精品电影| 国语性猛交xxxx乱大交| 777成影片免费观看| 国产成人免费A在线视频| 美女被免费视频网站a| 再深一点再重一点| 欧美深夜福利视频| 亚洲一区电影在线观看| 日本69xxxx| 三级黄色片在线观看| 国内自产一区c区| 6580岁老太婆| 国产在播放一区| 精品久久久久久中文字幕无码软件| 免费a级在线观看完整片| 欧美亚洲国产精品久久| 久久精品麻豆日日躁夜夜躁| 成人免费无码大片a毛片软件| v11av18| 国产熟女AA级毛片|